Bobcat Skid Steer Loader logo

BOBCAT Loader Fault Codes DTC

BOBCAT Skid Steer Loader Fault Codes DTC list

 

01-16 is not connected air filter

 

01-17 clogged air filter

 

02-16 Filter hydraulic / hydrostatic system is not connected

 

02-17 Filter hydraulic / hydrostatic system is connected

 

03-09 Low battery voltage

 

03-10 High Voltage Battery

 

03-11 Extremely high voltage battery

 

03-14 Extremely low battery voltage

 

03-22 Battery voltage is below the limit

 

04-09 Low levels of engine oil pressure

 

04-14 Extremely low levels of engine oil pressure

 

04-15 Engine oil pressure at the level of the emergency engine shutdown

 

04-21 Engine oil pressure above the maximum permissible

 

04-22 Engine oil pressure below the limit

 

05-09 Low supply pressure in the hydraulic system

 

05-10 High charge pressure in the hydraulic system

 

BOBCAT Error Codes DTC

05-11 Extremely high charge pressure in the hydraulic system

 

05-14 Extremely low supply pressure in the hydraulic system

 

05-15 charge pressure in the hydraulic system at the level of the emergency engine shutdown

 

05-21 charge pressure in the hydraulic system above the maximum permissible

 

05-22 charge pressure in the hydraulic system below the limit

 

06-10 high engine speeds

 

06-11 Extremely high engine speed

 

06-13 No engine speed signal

 

06-15 Engine speed at the level of the emergency engine shutdown

 

06-18 Engine speed is out of range

 

07-10 Heat the oil in the hydraulic system

 

07-11 Extremely high temperature hydraulic oil

 

07-15 The oil temperature in the hydraulic system at the level of the emergency engine shutdown

 

07-21 The oil temperature in the hydraulic system above the maximum allowable

 

07-22 The oil temperature in the hydraulic system below the limit

 

08-10 High engine coolant temperature

 

08-11 Extremely high engine coolant temperature

 

08-15 Engine coolant temperature at the level of the emergency engine shutdown

 

08-21 Engine coolant temperature is higher than the maximum permissible

 

08-22 Engine coolant temperature is below the limit

 

09-09 Low fuel level

09-21 Fuel level above the maximum permissible

 

09-22 Fuel level below the limit

 

10-17 clogged hydraulic filter discharge

 

11-05 frame sensor security shorted to battery

 

11-06 frame sensor security shorted to ground

 

12-21 Signal ShIMkontrollera front ext. hydraulics for the upper limit of the range

 

12-22 ShIMkontroller front ext. hydraulics for the lower range

 

12-23 ShIMkontroller front ext. Hydraulic not in the neutral range

 

13-05 Retaining fuel cutoff solenoid shorted to battery

 

13-06 Retaining fuel cutoff solenoid shorted to ground

 

13.7 Open circuit solenoid fuel cutoff

 

14-02 retracting solenoid fuel cutoff, the erroneous inclusion

 

14-03 retracting solenoid fuel cutoff, erroneous shutdown

 

15-02 retracting solenoid lock rods, erroneous inclusion

 

15-03 retracting solenoid lock rods, erroneous shutdown

 

16-05 Retaining solenoid lock rods shorted to battery

 

16-06 Retaining solenoid locking rod is closed to ground

 

17-05 hydraulic solenoid shut-off valve is closed to battery

 

17-06 hydraulic solenoid shut-off valve is closed to ground

 

17-07 Open circuit hydraulic solenoid shut-off valve

 

Fault Codes DTC list of BOBCAT Tractors

18-05 The solenoid slide is closed to battery

 

18-06 Solenoid spool is closed to ground

 

18-07 Open circuit solenoid spool

 

19-02 solenoid positioning bucket erroneous inclusion

 

19-03 Solenoid bucket positioning, incorrect shutdown

 

20-02 Solenoid switching speeds erroneous inclusion

 

20-03 Solenoid switching speeds, erroneous shutdown

 

21-02 Glow plugs the erroneous inclusion

 

21-03 Glow plugs, faulty shutdown

 

Starter 22-02, the erroneous inclusion

 

Starter 22-03, erroneous shutdown

 

23-02 Rear base solenoid erroneous inclusion

 

23-03 Rear base solenoid erroneous shutdown

 

24-02 Rear spindle solenoid erroneous inclusion

 

24-03 Rear spindle solenoid erroneous shutdown

 

25-02 Rear auxiliary proportional solenoid erroneous inclusion

 

25-03 Rear auxiliary proportional solenoid, faulty shutdown

 

27-02 erroneous inclusion of the stem of the front solenoid 

 

28.2 Solenoid relief valve, faulty switch

 

28.3 Solenoid relief valve, faulty shutdown

 

29.2 Solenoid large supply, faulty switch

 

29.3 Solenoid large supply, faulty shutdown

 

30-28 Failure memory controller

 

31-28 Fault recovery mode (also appears after the software update)

 

32-04 Advanced Management (ACS) does not communicate with the controller Bobcat

 

32-23 Calibration required ACS

 

32-24 Calibrate ACS

 

32-31 Fault actuator tilt ACS

 

Faulty wiring 32-32 tilt actuator ACS

 

32-33 tilt handle the wiring ACS

 

32-34 ACS tilt actuator is not in the neutral position

 

32-35 The handle / pedal tilt bucket ACS is not in the neutral position

 

32-36 Fault actuator lift ACS

 

Faulty wiring 32-37 actuator lift ACS

 

32-38 the wiring arm lifting ACS

 

32-39 actuator lifting ACS not in the neutral position

 

32-40 The handle / lift pedal bucket ACS is not in the neutral position

 

32-41 ACS: no connection

 

32-49 actuator lift ASS closed to ground

 

32-50 tilt actuator ASS shorted to ground

 

32-51 actuator lift ASS shorted to battery

 

32-52 tilt actuator ASS shorted to battery

 

32-53 Handle / foot boom is closed to ground, ASS

 

32-54 Handle / foot slope of the boom is closed to ground, ASS

 

32-55 Handle / foot boom is closed to battery, ACS

 

32-56 Handle / foot slope of the boom is closed to battery, ACS

 

32-57 Reduced performance actuator lift ACS

 

32-58 Reduced performance actuator tilt ACS

 

32-59 Wrong direction of the actuator lift ACS

 

32-60 Wrong direction of the actuator lift ACS

 

32-61 Chain lock handle ACS shorted to ground

 

32-62 Chain lock handle ACS closed on battery

 

32-63 Chain lock pedals ACS is closed to ground

 

32-64 Chain lock pedals ACS closed on battery

 

32-65 Voltage sensor out of range ACS

 

32-66 Battery voltage ACS below the limit

 

32-67 Switch ACS switched during operation

 

32-68 Error Information Handle boom, ACS

 

32-70 Chain right arm movements ACS shorted to ground

 

32-71 Chain right arm movements ACS closed on battery

 

32-74 X-axis joystick left ACS is out of range

 

32-75 Power Off unswitched equipment ACS

 

32-76 Error Information joystick CAN, ACS

 

32-77 Error Information remote control, ACS

 

33-23 The main controller (controller Bobcat) is not programmed

 

34-04 panel with push-button starting the controller does not communicate with Bobcat

 

35-02 erroneous inclusion of the fan hydraulics

 

35-03 Mistaken off the fan hydraulics

 

36-48 connect multiple controllers ACD

 

37-02 Two-speed auxiliary switch speeds erroneous inclusion

 

37-03 Two-speed auxiliary switch speeds erroneous inclusion

 

38-01 Error Information joystick CAN

 

38-02 Error Information Remote Control

 

38-04 There is no communication with the controller joystick

 

38-05 X axis the left stick is not in the neutral position

 

38-06 X axis right stick is not in the neutral position

 

38-07 Y-axis of the left joystick is not in neutral

 

38-08 Y-axis right stick is not in the neutral position

 

38-09 mode switch control circuit to the battery or to ground

 

38-10 Calibrate actuator

 

38-11 lift actuator is not in the neutral position

 

38-12 tilt actuator is not in the neutral position

 

38-13 Failure of the actuator lift

38-14 Failure of the actuator tilt

 

38-15 Wiring Fault speed control right wheel

 

38-16 Wiring fault for the speed of the left wheel

 

38-17 Reduced performance actuator tilt

 

38-18 Reduced performance actuator lift

 

38-19 X-axis joystick for left upper range

 

38-20 X-axis right joystick for the upper limit of the range

 

38-21 Y-axis joystick for left upper range

 

38-22 Y-axis right joystick for the upper limit of the range

 

38-23 front right sensor signal controls the upper limit of the range

 

38-24 front left sensor signal controls the upper limit of the range

 

38-25 rear right sensor signal controls the upper limit of the range

 

38-26 rear left sensor signal controls the upper limit of the range

 

38-27 Signal actuator for lifting the upper range

 

38-28 Signal actuator for tilting the upper range

 

38-29 X-axis joystick left for lower range

 

38-30 X-axis right joystick for the lower range

 

38-31 Y-axis joystick left for lower range

 

38-32 Y-axis right joystick for the lower range

 

38-33 front right sensor signal controls the lower end of the range

 

38-34 front left sensor signal controls the lower end of the range

 

38-35 rear right sensor signal controls the lower end of the range

 

38-36 rear left sensor signal controls the lower end of the range

 

38-37 Power "1" 5-volt sensor for the lower range

 

38-38 Power "2" 5-volt sensor for the lower range

 

38-39 actuator lift is closed to ground / lower boundary of the range

 

38-40 tilt actuator is closed to ground / signal for the lower range

 

38-41 Wrong direction of the tilt actuator

 

38-42 Wrong direction of the actuator lift

 

38-43 left front solenoid actuator erroneous inclusion

 

38-44 Solenoid left reverse drive, faulty switch

 

38-45 right front solenoid actuator erroneous inclusion

 

38-46 Solenoid right reverse drive, faulty switch

 

38-47 Front right solenoid control switch faulty

 

38-48 Front left solenoid control switch faulty

 

38-49 Rear right solenoid control switch faulty

 

38-50 Rear left solenoid control off erroneous

 

38-51 solenoid pressure control system, the erroneous inclusion

 

38-52 Back-up alarm, the erroneous inclusion

 

38-53 Solenoid left front drive off false

 

38-54 Solenoid left reverse drive, faulty shutdown

 

38-55 right front solenoid drive off false

 

38-56 Solenoid right reverse drive, faulty shutdown

 

38-57 Front right solenoid control extension, erroneous shutdown

 

38-58 Front right solenoid control retraction, erroneous shutdown

 

38-59 Front left solenoid control extension, erroneous shutdown

 

38-60 Front left solenoid control retraction, erroneous shutdown

 

38-61 Rear right solenoid control extension, erroneous shutdown

 

38-62 Rear right solenoid control retraction, erroneous shutdown

 

38-63 Rear left solenoid control extension, erroneous shutdown

 

38-64 Rear left solenoid control retraction, erroneous shutdown

 

38-65 solenoid pressure control system, faulty shutdown

 

38-66 Back-up alarm, erroneous shutdown

 

38-67 No communication from Bobcat controller

 

38-68 wheel alignment (alignment) not calibrated

 

38-69 Fault calibration actuators lift and tilt

 

38-70 Fault recovery mode range

 

38-71 Battery voltage out of limits

 

38-72 Pump drive is not calibrated

 

38-73 Control Mode Switch switched during operation

 

38-74 Uncontrolled rotation speed of the right wheel

 

38-75 Uncontrolled rotation speed of the left wheel

 

38-76 solenoid pressure control system Undercurrent

 

38-77 Front right solenoid control extension Undercurrent

 

38-78 Front right solenoid control retraction Undercurrent

 

38-79 Front left solenoid control extension Undercurrent

 

38-80 Front left solenoid control retraction Undercurrent

 

38-81 Rear right solenoid control extension Undercurrent

 

38-82 Rear right solenoid control retraction Undercurrent

 

38-83 Rear left solenoid control extension Undercurrent

 

38-84 Rear left solenoid control retraction Undercurrent

 

38-85 Power "1" 5-volt sensor for the upper limit of the range

 

38-86 ° Power "2" 5-volt sensor for the upper limit of the range

 

38-87 Problem front right steering device for the lower range

 

38-88 Malfunction of the front left of the steering gear

 

38-89 Fault rear right of the steering gear

 

Error 38-90 rear left control

 

38-91 No speed sensor impulses of the right wheel

 

38-92 No speed sensor impulses left wheel

 

38-93 right wheel speed sensor does not respond

 

38-94 left wheel speed sensor does not respond

 

38-95 Change of direction in the left wheel speed sensor

 

38-96 Change of direction in the right wheel speed sensor

 

38-98 controller in calibration mode drive

 

38-99 controller in calibration mode wheel position

39-04 Left joystick has no communication with the controller Bobcat

 

39-05 X-axis is not in the neutral position

 

 

39-07 Y-axis is not in the neutral position

 

 

39-12 manipulator switch left stick is not in neutral

 

 

39-13 is not connected joystick handle left off

 

39-16 is not connected joystick left off

 

39-28 Internal fault of the left joystick

 

 

39-48 Left joystick, multi-mode

 

 

40-04 Right joystick has no communication with the controller Bobcat

 

 

40-05 X axis right stick is not in the neutral position

 

 

40-07 Y-axis right stick is not in the neutral position

 

 

40-12 manipulator switch right joystick is not in neutral

 

 

40-13 is not connected right stick handle

 

 

40-16 is not connected right stick

 

 

40-28 Internal fault of the right joystick

 

 

40-48 Right stick, multi-mode

 

 

41-09 Low voltage generator

 

 

41-10 High Voltage Generator

 

 

41-11 Extremely high voltage generator

 

 

44-02 Horn, the erroneous inclusion

 

 

44-03 Horn, erroneous shutdown

 

 

45-02 The right turn signal, the erroneous inclusion

 

 

45-03 The right turn signal, erroneous shutdown

 

 

46-02 left turn signal, the erroneous inclusion

 

 

46-03 left turn signal, erroneous shutdown

 

 

47-21 Power 8voltovogo sensor for upper range

 

 

47-22 Power 8voltovogo sensor for lower range

 

 

48-02 front light switch, faulty switch

 

 

48-03 front light switch, faulty shutdown

 

 

49-02 Relay rear light erroneous inclusion

 

 

49-03 Relay rear light, faulty shutdown

 

60-21 signal lever back ext. hydraulics for the upper limit of the range

 

 

60-22 signal lever back ext. hydraulics for the lower range

 

 

60-23 lever rear ext. Hydraulic not in the neutral position

 

 

64-02 erroneous inclusion of a power relay

 

 

64-03 Mistaken off power relay

 

 

73-04 Fault remote control

 

 

73-13 Remote control signal is missing

 

 

74-72 Fault boot code controller Bobcat

 

 

75-01 Error Information joystick CAN

 

 

75-04 There is no communication with the controller drive

 

75-05 X axis the left stick is not in the neutral position

 

 

75-07 Y-axis of the left joystick is not in neutral

 

 

75-08 Y-axis right stick is not in the neutral position

 

 

75-09 mode switch ISO / H circuit to battery or to ground

 

 

75-13 jammed angle sensor right front wheel

 

 

75-14 jammed angle sensor left front wheel

 

 

75-15 jammed angle sensor right rear wheel

 

 

75-16 jammed angle sensor left rear wheel

 

 

75-17 left inclined plate is not in the neutral position

 

 

75-18 right oblique plate is not in the neutral position

 

 

75-19 X-axis joystick for left upper range

 

 

75-21 Y-axis joystick for left upper range

 

 

75-22 Y-axis right joystick for the upper limit of the range

 

 

75-23 Signal angle sensor right front wheel of the upper limit of the range

 

 

75-24 Signal angle sensor left front wheel of the upper limit of the range

 

 

75-25 Signal angle sensor right rear wheel for the upper limit of the range

 

 

75-26 Signal angle sensor left rear wheel of the upper limit of the range

 

 

75-27 Offset left oblique plate

 

 

75-28 Offset right oblique plate

 

 

75-29 X-axis joystick left for lower range

 

75-31 Y-axis joystick left for lower range

 

 

75-32 Y-axis right joystick for the lower range

 

 

75-33 Signal angle sensor right front wheel of the lower boundary of the range

 

75-34 Signal angle sensor left front wheel of the lower boundary of the range

 

75-35 Signal angle sensor right rear wheel of the lower boundary of the range

 

 

75-36 Signal angle sensor left rear wheel of the lower boundary of the range

 

 

75-37 Power "1" 5-volt sensor for the lower range

 

 

75-38 Sensor supply 2 for the lower range

 

75-39 Sensor Signal Left inclined plate for the top end of the range

 

75-40 Sensor Signal Left inclined plate for bottom of the range

 

 

75-41 Sensor Signal Right inclined plate for the top end of the range

 

 

75-42 Sensor Signal Right inclined plate for bottom of the range

 

 

75-43 left front solenoid actuator erroneous inclusion

 

 

75-44 Solenoid left reverse drive, faulty switch

 

 

75-45 right front solenoid actuator erroneous inclusion

 

 

75-46 Solenoid right reverse drive, faulty switch

 

 

75-47 Front right solenoid control extension shorted to battery

 

 

75-48 Front left solenoid control extension shorted to battery

 

 

75-49 Rear right solenoid control extension shorted to battery

 

 

75-50 Rear left solenoid control extension shorted to battery

 

 

75-51 solenoid pressure control system is closed to battery

 

 

75-52 Back-up alarm, the erroneous inclusion

 

 

75-53 Solenoid left front drive off false

 

 

75-54 Solenoid left reverse drive, faulty shutdown

 

 

75-55 right front solenoid drive off false

 

 

75-56 Solenoid right reverse drive, faulty shutdown

 

 

75-57 Front right solenoid control extension shorted to ground

 

75-58 Front right solenoid control retraction shorted to ground

 

75-59 Front left solenoid control extension shorted to ground

 

 

75-60 Front left solenoid control retraction shorted to ground

 

 

75-61 Rear right solenoid control extension shorted to ground

 

 

75-62 Rear right solenoid control retraction shorted to ground

 

 

75-63 Rear left solenoid control extension shorted to ground

 

 

75-64 Rear left solenoid control retraction shorted to ground

 

 

75-65 solenoid pressure control system is closed to ground

 

 

75-66 Back-up alarm, erroneous shutdown

 

 

75-67 No communication from Bobcat controller

 

 

75-68 angle sensors are not calibrated

 

 

75-69 Battery voltage is above the maximum permissible

 

 

75-70 Fault recovery mode (also appears after the software update)

 

75-71 Battery voltage is below the limit

 

 

75-72 Pump drive is not calibrated

 

 

75-73 mode switch ISO / H switched during operation

 

 

75-74 Uncontrolled rotation speed of the right wheel

 

 

75-75 Uncontrolled rotation speed of the left wheel

 

 

75-76 There are no posts from the controller ACS

 

 

75-77 speed sensor signal of the left wheel of the upper limit of the range

 

75-78 speed sensor signal of the right wheel of the top of the range

 

 

75-79 speed sensor signal of the left wheel of the lower boundary of the range

 

 

75-80 speed sensor signal of the right wheel of the bottom of the range

 

 

75-81 Front right solenoid control retraction shorted to battery

 

75-82 Front left solenoid control retraction shorted to battery

 

 

75-83 Rear right solenoid control retraction shorted to battery

 

 

75-84 Rear left solenoid control retraction shorted to battery

 

 

75-85 Power "1" 5-volt sensor for the upper limit of the range

 

 

75-86 Sensor supply 2 for the upper limit

 

 

75-88 controller in programming mode

 

 

75-91 Changing the polarity of the left oblique sensor plate

 

 

75-92 Changing the polarity of the sensor right oblique plate

 

 

75-93 right wheel speed sensor does not respond

 

 

75-94 left wheel speed sensor does not respond

 

 

75-95 Change of direction in the left wheel speed sensor

 

 

75-96 Change of direction in the right wheel speed sensor

 

 

75-98 controller in calibration mode

 

 

76-73 left panel, the error of the receiver

 

 

77-48 Ignition Switch, multi-mode

 

 

78-74 Door / locking the lock is opened / closed

 

 

80-02 ACD, output «A», the erroneous inclusion

 

 

80-03 ACD, output «A», erroneous shutdown

 

 

81-02 ACD, exit «B», the erroneous inclusion

 

 

81-03 ACD, exit «B», erroneous shutdown

 

82-02 ACD, output «C», the erroneous inclusion

 

 

82-03 ACD, output «C», erroneous shutdown

 

83-02 ACD, exit «D», the erroneous inclusion

 

 

83-03 ACD, exit «D», erroneous shutdown

 

 

84-02 ACD, exit «E», the erroneous inclusion

 

 

84-03 ACD, exit «E», erroneous shutdown

 

 

85-02 ACD (controller attachments), exit «F», the erroneous inclusion

 

 

85-03 ACD, exit «F», erroneous shutdown

 

 

86-02 ACD, exit «G», the erroneous inclusion

 

86-03 ACD, exit «G», erroneous shutdown

 

 

87-02 ACD, exit «H», the erroneous inclusion

 

 

87-03 ACD, exit «H», erroneous shutdown

 

 

90-02 Service Output «C», the erroneous inclusion

 

 

90-03 Service Output «C», erroneous off wheels

 

 

91-02 Service Output «D», the erroneous inclusion

 

 

91-03 Service Output «D», erroneous shutdown

 

 

92-02 Service Output "E", the erroneous inclusion

 

 

92-03 Service Output "E" erroneous shutdown

 

 

93-02 Service Output «F», the erroneous inclusion

 

 

93-03 Service Output «F», erroneous shutdown

Comments: 0