MAN Logo
Download
MAN truck Fault Codes DTC
MAN truck Fault Codes DTC
MAN truck Fault Codes DTC.pdf
Adobe Acrobat Document 473.2 KB

MAN Truck ZBR Fault Codes DTC

MAN Fault Code ZBR DTC (SPN) Description Reason, verification and system response.

 

00038 Reserve, the fuel level in the tank 2. Priority 5: Display during stop and while driving. Fault: 1. too high; 2. Too low; 3. Unacceptable; 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: R1 / 14.

 

00070 Signal "parking brake". Priority 2: The fault, which requires removal of the service center. Fault: 8. Wrong signal.

 

00096 Reserve, the fuel level in the tank 1. Priority 5: Display during stop and while driving. Fault: 1. too high; 2. Too low; 3. Unacceptable; 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: R1 / 13.

00098 Engine oil level.

 

00100 Signal "Engine oil pressure." Priority 4: No display does not affect the operability. Fault: 8. Wrong signal.

 

00102 Signal "pressure air charge." A warning light on the instrument panel constantly lit in red, and when moving or stopped. Instead, the real pressure signal is simulated by a replacement signal. The engine is an inadequate amount of air, in consequence, significantly reduced power. Faulty sensor, broken wire, loose contacts, intercooler (intercooler) is blocked or forced air system is not tight.

 

00110 Signal "Engine coolant temperature". Priority 4: No display does not affect the operability. Fault: 8. Wrong signal.

 

00111 Signal "Engine coolant level". Priority 5: Display during stop and while driving. Fault: 6. Short to Ubat .; 10. Open. Pinout A302: R1 / 13.

 

00158 ZBR2 voltage power when the ignition (terminal 15, ignition). Priority 2: The fault, which requires removal of the service center. Pinout A302: ZE17.

 

00159 margin, the level of the gas pressure in the tank. Priority 2: The fault, which requires removal of the service center. Fault: 1. too high; 2. Too low; 5. Short to Ground; 6. Short to Ubat. Pinout A302: X / 1.

 

00168 ZBR2 voltage supply, plus a constant battery missing (terminal 30-0 Ubat.). Priority 1: Requires stopping the engine. Fault: 1. too high; 2. Too low; 10. Open. Pinout A302: ZE / 18.

 

00171 The temperature of the outside air.

 

00175 The oil temperature in the engine.

 

00190 engine speeds. A warning light on the instrument panel constantly lit in red, and when moving or stopped. The engine can not be started or the engine may stall spontaneously. Registration and collection of data on the signal of cranked and distributive shaft motor rotation speed is not functioning.

 

00513 Engine torque.

 

00520 Signal "The weakening of the braking retarder". Priority 4: No display does not affect the operability. Fault: 8. Wrong signal.

 

00597 Signal "Brake ABS, ASR, EBS" Priority 2: Fault requiring removal of the service center. Fault: 8. Wrong signal.

 

00639 Data Bus T-CAN Higt, serial communication. Priority 1: Requires stopping the engine. Fault: 4. No signal. Pinout A302 M / 1.

 

00639 Data Bus T-CAN Low, serial communication. Priority 1: Requires stopping the engine. Fault: 4. No signal. Pinout A302 M / 7.

 

00767 Including the transfer of R. Priority 2: Fault requiring removal of the service center. Fault: 5. Short to Ground. Pinout A302 M / 6.

 

01007 Brake function replacement.

 

01031 function replacement parking lighting.

 

01086 residual pressure in the circuit 3 electric pneumatic system (ECAM). Priority 1: Requires the engine stop or Priority 2: Fault requiring removal of the service center. Fault: 1. too high; 2. Too low; 4. The signal is absent; 6. Short to Ubat. Pinout A302: R1 / 8.

 

01087 residual pressure in the circuit 1 electric pneumatic system (ECAM). Priority 1: Requires stopping the engine. Fault: 1. too high; 2. Too low; 4. The signal is absent; 6. Short to Ubat. Pinout A302: R1 / 11.

 

01088 2 residual pressure in the circuit of electric pneumatic system (ECAM). Priority 1: Requires stopping the engine. Fault: 1. too high; 2. Too low; 4. The signal is absent; 6. Short to Ubat. Pinout A302: R1 / 9.

 

01089 residual pressure in the electric circuit 4 of the pneumatic system (ECAM). Priority 1: Requires stopping the engine. Fault: 1. too high; 2. Too low; 4. The signal is absent; 6. Short to Ubat. Pinout A302 M / 2.

 

01235 data bus I-CAN Higt, serial communication. Priority 1: Requires stopping the engine. Fault: 4. No signal. Pinout A302: R2 / 9.

 

01235 data bus I-CAN Low, serial communication. Priority 1: Requires stopping the engine. Fault: 4. No signal. Pinout A302: R2 / 10.

 

01376 ZBR2 voltage supply, plus a constant battery missing (terminal 30-1 Ubat.). Priority 1: Requires stopping the engine. Fault: 1. too high; 2. Too low; 10. Open. Pinout A302: ZE / 13.

 

01624 Vehicle speed.

 

01667 braking signal retarder (timeout). Priority 2: The fault, which requires removal of the service center. Fault: 8. Wrong signal.

 

02987 Chassis number in the tachograph or ZBR2 parameters do not fit to the car. Priority 1: Requires stopping the engine. Fault: 3. Unacceptable.

 

03000 ZBR2 system, information about emergency shutdown. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground. Pinout A302: F1 / 12.

 

03001 ZBR2 system, wake up the computer. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground. Pinout A302: F1 / 11.

 

03102 Terminal 30-1 is connected. Priority 1: Requires stopping the engine. Fault: 1. too high; 2. Too low; 10. Open. Pinout A302: ZE / 9.

 

03103 ZBR2 voltage supply, analog ground. Pinout A302 M / 16.

 

03104 ZBR2 voltage supply, analog ground. Pinout A302: R1 / 15.

 

03107 ZBR2 voltage supply, ignition switched on (relay terminal 15). Priority 2: The fault, which requires removal of the service center. Fault: 5. Short to Ground; 10. Open. Pinout A302: F2 / 12.

 

03108 ZBR2 voltage supply batteries power switch. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 10. Open. Pinout A302: F2 / 18.

 

03111 ZBR2 voltage supply, starter switch (terminal 50). Priority 1: Requires stopping the engine. Priority 2: The fault, which requires removal of the service center. Priority 3: Display during stop. Priority 4: No display does not affect the operability. Priority 5: Display during stop and while driving. Pinout A302: ZE / 5.

 

03201 The pressure drop on the air filter of the engine. Priority 5: Display during stop and while driving. Fault: Too low 2; 5. Short to Ground; 6. Short to Ubat. Pinout A302: X / 3.

 

03300 Generator, W. Terminal Priority 2: Fault requiring removal of the service center. Fault: 3. Unacceptable. Pinout A302 M / 14.

 

03301 Generator, L. The terminal Priority 2: Fault requiring removal of the service center. Fault: 4. No signal. Pinout A302 M / 4.

 

03302 generator terminal B +. Priority 3: Display during stop. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302 M / 8.

 

03303 Signal D + (engine running). Priority 2: The fault, which requires removal of the service center. Fault: 5. Short to Ground; 6. Short to Ubat. Pinout A302: F2 / 17.

 

03335 Supply voltage (no data). Priority 4: No display does not affect the operability. Fault: Fault 0 is missing or faulty control unit.

 

03400 Solenoid valve for preheating. Priority 3: Display during stop. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302 M / 13.

 

03401 Relay preheating. Priority 3: Display during stop. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: ZE / 8.

 

03402 Current glow plugs. Priority 3: Display during stop. Fault: 10. Open. Pinout A302: ZE / 19.

 

03403 Current glow plugs. Priority 3: Display during stop. Fault: Too low 2; 3. Unacceptable; 10. Open. Pinout A302: ZE / 20.

 

03500 Malfunction trailer ABS (ABS, ASR, EBS). Priority 5: Display during stop and while driving. Fault: Fault 0 is missing or faulty control unit. Pinout A302: X / 2.

 

03501 trailer ABS, power consumption. Priority 5: Display during stop and while driving. Fault: 1. too high; 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: R2 / 14.

 

03502 tractor braking signal. Priority 2: The fault, which requires removal of the service center. Fault: 1. too high; 2. Too low; 5. Short to Ground; 6. Closing naUbat .; 10. Open. Pinout A302: R2 / 4.

 

03503 braking signal trailer. Priority 2: The fault, which requires removal of the service center. Fault: 1. too high; 2. Too low; 5. Short to Ground; 6. Closing naUbat .; 10. Open. Pinout A302: R2 / 5.

 

03568 retarder is enabled. Fault: Fault 0 is missing or faulty control unit.

 

03569 engine brake is turned on. Fault: Fault 0 is missing or faulty control unit.

 

03570 The service brakes are included. Fault: Fault 0 is missing or faulty control unit.

 

03600 The fluid level in the clutch. Priority 5: Display during stop and while driving. Fault: 6. Short to Ubat .; 10. Open. Pinout A302: R1 / 2.

 

03602 Relay reversing light. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F2 / 13.

 

03603 Turning otopleniyaKongsberg system. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302 M / 18.

 

03625 Creep speed. Priority 2: The fault, which requires removal of the service center. Fault: 6. Short to Ubat. Pinout A302: X / 4.

 

03800 front axle level (air podveskaECAS). Priority 5: Display during stop and while driving. Fault: Fault 0 is missing or faulty control unit; 4. The signal is absent; 5. Short circuit to ground. Pinout A302: R2 / 17.

 

03903 The fuel temperature in the tank 1. Priority 5: Display during stop and while driving. Fault: 1. too high; 2. too low. Pinout A302: R1 / 10.

04000 switch headlights. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F1 / 17.

 

04001 Dipped beam, left side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: BL / 6.

 

04002 Dipped beam, right side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: BR / 2.

 

04003 Left headlamp height adjustment. Priority 5: Display during stop and while driving. Fault: Fault 0 is missing or faulty control unit; 3. Unacceptable; 4. The signal is absent; 8. wrong signal; 9. Faulty component. Pinout A302: BL / 3.

 

04004 Right headlamp height adjustment. Priority 5: Display during stop and while driving. Fault: Fault 0 is missing or faulty control unit; 3. Unacceptable; 4. The signal is absent; 8. wrong signal; 9. Faulty component. Pinout A302: BR / 6.

 

04005 Turning on the tractor, left rear. Priority 5: Display during stop and while driving. Fault: 1. too high; 2. Too low; 5. Short to Ground; 6. Closing naUbat .; 10. Open. Pinout A302: R2 / 1.

 

04006 Turning on the tractor, right rear. Priority 5: Display during stop and while driving. Fault: 1. too high; 2. Too low; 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: R2 / 13.

 

04007 Turning on the towing vehicle, or the front left side. Priority 5: Display during stop and while driving. Fault: 1. too high; 2. Too low; 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: BL / 4.

 

04008 Turning on the tractor, right front or side. Priority 5: Display during stop and while driving. Pinout A302: BR / 3.

 

04009 switch turns the pointer, the Hall sensor (on the steering wheel to the left). Priority 5: Display during stop and while driving. Fault: 6. Short to Ubat .; Pinout A302: F1 / 3.

 

04010 switch turns the pointer, the Hall sensor (on the steering wheel to the right). Priority 5: Display during stop and while driving. Fault: 6. Short to Ubat .; Pinout A302: F1 / 6.

 

04011 Switch flashing light on the left. Priority 5: Display during stop and while driving. Fault: 6. Short to Ubat .; 10. Open. Pinout A302: F1 / 15.

 

04012 Switch flashing light on the right. Priority 5: Display during stop and while driving. Fault: 6. Short to Ubat .; 10. Open. Pinout A302: F1 / 16.

 

04013 Alarm, warning lamp. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F2 / 16.

 

04014 Alarm, switch. Priority 2: The fault, which requires removal of the service center. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F1 / 1.

 

04015 Turning on the trailer to the left. Priority 5: Display during stop and while driving. Fault: 1. too high; 2. Too low; 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: R2 / 3.

 

04016 Turning on the trailer, right. Priority 5: Display during stop and while driving. Fault: 1. too high; 2. Too low; 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: R2 / 2.

 

04017 Main beam, left side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: BL / 5.

 

04018 Main beam, right side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: BR / 1.

 

04019 Main beam, push button. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F1 / 13.

 

04020 Intermittent headlights, push button.

04021 additional main beam, left side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: BL / 1.

 

04022 additional high beam, right side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: BR / 4.

 

04023 additional high beams on the roof of the relay. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F2 / 14.

 

04024 Rear fog lights on the tractor. Priority 5: Display during stop and while driving. Fault: 1. too high; 2. Too low; 5. Short to Ground; 6. Short to Ubat .; Pinout A302: R2 / 16.

 

04025 Rear fog lights on the trailer. Priority 5: Display during stop and while driving. Fault: 1. too high; 2. Too low; 5. Short to Ground; 6. Short to Ubat .; Pinout A302: R2 / 15.

 

04026 Fog lights, right side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: BR / 5.

 

04027 Fog lights, left side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: BL / 2.

 

04028 Control lamp fog lights, unlocking inclusion. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; Pinout A302: X / 12.

 

04029 Additional fog lamp relay. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F2 / 18.

 

04030 Lanterns parking lights on the vehicle right side. Priority 5: Display during stop and while driving. Fault: Fault 0 is missing or faulty control unit; 1. Too high; 2. Too low; 10. Open. Pinout A302: ZE / 1.

 

04031 Lanterns parking lights on the vehicle left side. Priority 5: Display during stop and while driving. Fault: Fault 0 is missing or faulty control unit; 1. Too high; 2. Too low; 10. Open. Pinout A302: ZE / 7.

 

04032 Lanterns parking light, right side. Priority 5: Display during stop and while driving. Fault: 3. Unacceptable. Pinout A302: ZE / 10.

 

04033 Lanterns parking light, left side. Priority 5: Display during stop and while driving. Fault: 3. Unacceptable. Pinout A302: ZE / 14.

 

04034 Side marker lights, right side. Priority 5: Display during stop and while driving. Fault: 1. too high; 2. Too low; 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: R2 / 7.

 

04035 Side marker lights, left side. Priority 5: Display during stop and while driving. Fault: 1. too high; 2. Too low; 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: R2 / 6.

 

04036 Lanterns trailer parking light, right side. Priority 5: Display during stop and while driving. Fault: Fault 0 is missing or faulty control unit; 1. Too high; 2. Too low; 10. Open. Pinout A302: ZE / 3.

 

04037 Lanterns trailer parking light, left side. Priority 5: Display during stop and while driving. Fault: Fault 0 is missing or faulty control unit; 1. Too high; 2. Too low; 10. Open. Pinout A302: ZE / 2.

 

04038 parking light switch. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: ZE / 4.

 

04039 Switch parking light. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F1 / 14.

 

04040 Winter mode switch. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F2 / 18.

 

04042 Check the lighting. Priority 6: An indication of the critical state of security. 0. The fault is missing or defective control unit.

 

04043 Checking lighting lock. Priority 4: No display does not affect the operability. Fault: Fault 0 is missing or faulty control unit.

 

04044 Check lighting unlock. Priority 4: No display does not affect the operability. Fault: Fault 0 is missing or faulty control unit.

 

04045 System indicator lamps on both sides, including. Priority 5: Display during stop and while driving. Fault: 3. Unacceptable.

 

04046 calibration Identification of the headlamps angle system. Priority 4: No display does not affect the operability. Fault: Fault 0 is missing or faulty control unit.

 

04100 Middle winter light, right side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: BR / 2.

 

04101 Middle winter light, left side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: BL / 6.

 

04102 Far winter light, right side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: BR / 1.

 

04103 Far winter light, left side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: BL / 5.

 

04104 Lanterns back winter parking light, right side. Priority 5: Display during stop and while driving. Fault: Fault 0 is missing or faulty control unit; 1. Too high; 2. Too low; 10. Open. Pinout A302: ZE / 1.

 

04105 Tail light winter parking light, left side. Priority 5: Display during stop and while driving. Fault: Fault 0 is missing or faulty control unit; 1. Too high; 2. Too low; 10. Open. Pinout A302: ZE / 7.

 

04109 Switch camouflage headlight. Priority 5: Display during stop and while driving. Pinout A302: F1 / 2.

 

04113 Side light, right side, the relay. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: X / 17.

04200 interior lighting and lighting steps, right side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F2 / 5.

 

04201 interior lighting and lighting steps, left side. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F2 / 4.

 

04300 windshield washer fluid, the level sensor. Priority 5: Display during stop and while driving. Fault: Too low 2; 6. Short to Ubat. Pinout A302: F1 / 7.

 

04301 windshield washer fluid pump. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F2 / 15.

 

04302 wiper, intermittent switch. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; Pinout A302: F1 / 5.

 

04303 Wiper, master oscillator switches intermittent mode. Priority 2: The fault, which requires removal of the service center. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: X / 18.

 

04304 Washer, key switch. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; Pinout A302: F1 / 4.

 

04305 wiper, rain sensor signal presence. Priority 3: Display during stop. Pinout A302: F1 / 18.

 

04306 Windscreen washers, liquid level sensor. Priority 5: Display during stop and while driving. Fault: Too low 2; 6. Short to Ubat .; 10. Open. Pinout A302: R1 / 5.

 

04307 Windscreen washers, pump. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F2 / 1.

 

04308 Wiper Motor, speed. Priority 2: The fault, which requires removal of the service center. Pinout A302: F2 / 6.

 

04309 wiper motor, the speed of rotation. Priority 2: The fault, which requires removal of the service center. Pinout A302: F2 / 6.

 

04310 Wiper relay. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: ZE / 6.

 

04311 Limit the wiper switch. Priority 5: Display during stop and while driving. Fault: 3. Unacceptable; 4. The signal is absent. Pinout A302: F1 / 10.

 

04312 Wiper Switch. Priority 2: The fault, which requires removal of the service center. Pinout A302: X / 15.

 

04400 Central lubrication system, the amount of lubricant in the system. Priority 5: Display during stop and while driving. Fault: Too low 2; 6. Short to Ubat .; 10. Open. Pinout A302: F2 / 8.

 

04401 Central lubrication system, engine. Priority 5: Display during stop and while driving. Fault: 4 signal is absent; 5. Short circuit to ground. Pinout A302: X / 16.

 

04402 Central lubrication system, the pump gauge. Priority 5: Display during stop and while driving. Fault: 4 signal is absent; 6. Short to Ubat .; 10. Open. Pinout A302: F2 / 11.

04403 Central lubrication system, switch. Priority 5: Display during stop and while driving. Fault: 6. Short to Ubat .; Pinout A302: X / 6.

 

04500 Hydraulic steering system, oil level in one circuit. Priority 5: Display during stop and while driving. Fault: 6. Short to Ubat .; Pinout A302: R1 / 6.

 

04502 Hydraulic steering system, oil level in the 2 circuit. Priority 5: Display during stop and while driving. Fault: 6. Short to Ubat .; Pinout A302: R1 / 4.

 

04523 Hydraulic steering system, oil pressure in one circuit. Priority 2: The fault, which requires removal of the service center. Fault: 4 signal is absent; 5. Short circuit to ground. Pinout A302: X / 11.

 

04524 Hydraulic steering system, oil pressure in the circuit 2. Priority 2: The fault, which requires removal of the service center. Fault: 4 signal is absent; 5. Short circuit to ground. Pinout A302: X / 10.

 

04600 Door contact, right. Priority 5: Display during stop and while driving. Pinout A302: F1 / 8.

 

04601 Door contact, left. Priority 5: Display during stop and while driving. Pinout A302: F1 / 9.

 

04800 Mating alarm central lock. Priority 5: Display during stop and while driving. Fault: 3. Unacceptable. Pinout A302: X / 7.

 

05000 buzzer in the instrument panel. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; 10. Open. Pinout A302: F2 / 9.

 

05001 Lamp fault indication in the instrument panel. Priority 5: Display during stop and while driving. Fault: 5. Short to Ground; 6. Short to Ubat .; Pinout A302: X / 14.

 

05600 Fixing the cockpit. Priority 1: Requires stopping the engine. Fault: Fault 0 is missing or faulty control unit; 6. Short to Ubat .. Pin A302: R1 / 1.

 

05 700 Target position ACC (speed control system with automatic maintenance of a safe distance). Priority 2: The fault, which requires removal of the service center. Fault: 5. Short to Ground; 6. Short to Ubat .. Pin A302: F2 / 2.

 

06000 Tachograph TCO1, failure when receiving or sending a message. Priority 2: The fault, which requires removal of the service center. Fault: 8. wrong signal.

 

06001 ACC (control system with automatic speed maintaining a safe distance), failure when receiving or sending a message. Priority 5: Display during stop and while driving. Fault: 8. wrong signal.

 

06002 Date and time, failure when receiving or sending a message. Priority 2: The fault, which requires removal of the service center. Fault: 8. wrong signal.

 

06003 Control vehicle speed, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06004 Dashboard, failure when receiving or sending a message. Priority 2: The fault, which requires removal of the service center. Fault: 8. wrong signal.

 

06005 Post EBS1 EBS system (brake system with an electronically controlled), failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06006 Post ECAS1 sistemyECAS (air suspension with electronically controlled), failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06008 Post EEC1 (electronic motor controller), the FFR system (car computer), failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06009 Post ERC_REvspomogatelnogo retarder, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06010 Post ERC_RD primary retarder, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06011 oil pressure in the engine failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06012 Coolant temperature, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06013 Environmental conditions, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06016 Post EBS3 EBS system (brake system with an electronically controlled), failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06017 Post EBS4 EBS system (brake system with an electronically controlled), failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06018 Signal Engine speed, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06020 Post ETC2 sistemyFFR, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06021 Post ETC3 FFR system failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06022 Signal fuel consumption since the last reset, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 4. No signal.

 

06023 Signal fuel consumption in liters per hour, the failure at the reception or transmission of messages while driving. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06024 Details of the charge air pressure, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06025 Post TC1_FT sistemyFFR with automatic transmission failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06026 Notice of ACC1 ACC signal indication, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06027 Aux_stat_ZBR_1 signal is not transmitted through the channel dannyhT-CAN as 1 message failure when receiving or sending a message. Priority 4: No display does not affect the operability.

 

06028 Aux_stat_ZBR_1 signal is not transmitted on the channel I-CAN data as 1 message failure when receiving or sending a message. Priority 4: No display does not affect the operability.

 

06029 signal in the data channel I-CANukazatelya level in the tank washer fluid, failure when receiving or sending a message. Priority 4: No display does not affect the operability.

 

06030 Message motor tormozaERC1_RX by FFR, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06032 Aux_stat_ZBR_2 signal is not transmitted on the channel I-CAN data as 2 message failure when receiving or sending a message. Priority 4: No display does not affect the operability.

 

06033 Signal Aux_stat_ZBR_3 not transmitted data channel I-CAN as a message 3, failure when receiving or sending a message. Priority 4: No display does not affect the operability.

 

06034 Reserve Aux_stat_ZBR_4 signal is not transmitted through the data channel I-CAN as a message 4, failure when receiving or sending a message. Priority 4: No display does not affect the operability.

 

06035 Signal "Vehicle Power" in the CAN channel, voltage at terminal 30 and 15 of the EDC by the FFR, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06036 signal level of the liquid in the secondary retarder, the refusal of admission or when sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06037 signal level of the liquid in the primary retarder, refusal of admission or when sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06038 Post EEC2 2elektronnoy engine management system failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06039 Signal for the liquid level in the gearbox failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06040 signal for the load on the rear axle (EBS system), failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06041 Signal on loading the vehicle (ECAS system), failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06042 Signal for engine configuration failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06043 Message "SPN Response (MAN request for data)" for channel I-CAN data failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06044 Message "SPN Response (MAN request for data)" for channel I-CAN data failure when receiving or sending a message. Priority 4: No display does not affect the operability.

 

06045 Post ECAM1 channel data T-CAN, the remaining pressure signal failure when receiving or sending a message. Priority 4: No display does not affect the operability.

 

06046 Posted by WSK system (gidrotransformatornoe clutch), failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06047 Post VDC1 not accepted because of the failure of the data channel T-CAN, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06048 Post ETC2 channel I-CAN data failure when receiving or sending a message. Priority 4: No display does not affect the operability.

06050 Posted by DM1 ZBR2 channel I-CAN data failure when receiving or sending a message. Priority 4: No display does not affect the operability.

 

06051 Post DM1 fault memory and pamyatiOBDU (onboard diagnostic device), failure when receiving or sending a message. Priority 4: No display does not affect the operability.

 

06052 Notice of the chassis number on the channel I-CAN data failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06053 Posted by KSM2 (control device for external data exchange) via the data T-CAN, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06054 Post ASS1_A ECAS (air suspension with electronically controlled), failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06055 Post ASS1_B ECAS (air suspension with electronically controlled), failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06056 Post ASS1_B ECAS (air suspension with electronically controlled), failure when receiving or sending a message.

 

06057 Report on the chassis number on the channel I-CAN data failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06058 Signal Aux_Stat Inst2 channel I-CAN data on the data channel are no posts about switching, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06059 Post ESP, failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06060 Post ASS3 ECAS (air suspension with electronically controlled), failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06061 Notice of the vehicle weight by sistemyECAS (air suspension with electronically controlled), failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06062 Notice of the vehicle weight from the EBS (brake system with an electronically controlled), failure when receiving or sending a message. Priority 4: No display does not affect the operability. Fault: 8. wrong signal.

 

06202 Post Aux_stat_ZBR2 channel I-CAN data (manufacturer reserve for ZBR iliZBRO). Priority 4: No display does not affect the operability.

 

06203 Post Aux_stat_ZBR3 channel I-CAN data (manufacturer reserve for ZBR or ZBRO). Priority 4: No display does not affect the operability.

 

06204 Modified soobschenieETC2 channel I-CAN data (manufacturer reserve for ZBR or ZBRO). Priority 4: No display does not affect the operability.

 

06205 Message from the instrument panel through the channel I-CAN data (manufacturer reserve for ZBR or ZBRO). Priority 4: No display does not affect the operability.

 

06206 Post ECAM1 channel T-CAN data (manufacturer reserve for ZBR or ZBRO). Priority 4: No display does not affect the operability.

 

06207 Post ECAM1 channel I-CAN data (manufacturer reserve for ZBR or ZBRO). Priority 4: No display does not affect the operability.

 

06208 Post DM1 ZBR2 (manufacturer reserve for ZBR or ZBRO). Priority 5: Display during stop and while driving.

 

06209 Post DM1 OBDU channel I-CAN data (manufacturer reserve for ZBR or ZBRO). Priority 5: Display during stop and while driving.

 

06250 buffer CAN data communications channel is absent (the manufacturer reserves for ZBR or ZBRO). Priority 4: No display does not affect the operability. Fault: 4. No signal.

 

06251 messages in the channel dannyhCAN not processed (the manufacturer reserves for ZBR or ZBRO). Priority 4: No display does not affect the operability. Fault: 4. No signal.

 

06280 ROM error check (program code) (manufacturer reserve for ZBR or ZBRO). Priority 2: The fault, which requires removal of the service center. Fault: 3. Unacceptable.

 

06281 ROM check error (EOL option (factory programming)) (manufacturer reserve for ZBR or ZBRO). Priority 2: The fault, which requires removal of the service center. Fault: 3. Unacceptable.

 

06302 K-cable KWP2000 (a protocol for diagnosis using a PC), Serial communication. Priority 2: The fault, which requires removal of the service center. Pinout A302 M / 10.

 

06303 T-CAN Masse, serial communication. Pinout A302 M / 9.

 

06304 signal indicating temporary failure data channel T-CAN, serial communication. Priority 4: No display does not affect the operability. Fault: 4. No signal.

 

06305 signal the temporary failure I-CAN data channel serial communication. Priority 4: No display does not affect the operability. Fault: 4. No signal.

 

08010 Notice of the pressure drops below an acceptable level vECAM (air suspension with electronically controlled). Priority 1: Requires the engine stop or Priority 2: Fault requiring removal of the service center. Fault: 2. Too low.

 

08104 residual pressure in the circuit 5 (input circuit) in the ECAM system (air suspension with electronically controlled). Priority 1: Requires stopping the engine. Fault: 1. too high; 2. Too low; 4. The signal is absent; 6. Short to Ubat. Pinout A302 M / 15.

Comments: 0