Scania Fault Codes

Download
SCANIA FAULT CODES
SCANIA FAULT CODES
SCANIA FAULT CODES.pdf
Adobe Acrobat Document 44.7 KB

000 00 No Fault

01 001 less than the rated voltage - heater works

02 002 higher than the rated voltage - heater works

004 03 Short circuit fan (D2I)

005 05 Short-circuiting the wires from alarm (D2I)

009 09 Heater off system TRS (D2I / D9W)

010 0A higher than the nominal voltage (heater stopped)

011 0B voltage less than the nominal (heater stopped)

012 0C overheat - fuel pump is turned off

013 0D temperature sensor recorded a high temperature

014 0E big difference values ​​of t. sensor. overheating sensor. regulation. t (D3W / D9W)

015 0F heater overheated many times - the heater is turned off (D2I / D9W)

017 11 Reusable overheating (t exceeds the second threshold) (D3W)

020 14 Candle / rod defective bulbs

021 15 Short candle / bar bulbs

022 16 Faulty relays candle / bar bulbs (D2W)

023 17 Internal defect relay control R2 candle / bar bulbs

024 18 Short-circuit switch controller candle / bar bulbs

025 19 Short-circuit diagnostic socket

029 1D fan air gap 5 does not operate R3

030 1E air fan does not work in all positions (R3-D3W)

031 1F air fan does not work in all positions (R3-D3W)

032 20 Air fan does not work in all positions (R3-D3W)

033 21 Air fan does not work in all positions (R4-D2I / D9W)

034 22 there is no contact with the solenoid valve of the cooling system. (D2W / D9W)

035 23 No contact with the relay average performance

036 24 Short-circuit relay average performance

037 25 Do not rotate water pump (D2W / D9W)

038 26 No contact with the fan relay cab heating (D2W / D9W)

039 27 Short cab heating fan relay (D2W / D9W)

040 28 Short circuit solenoid. valve cooling system. (D2W / D9W)

042 2A Short circuit water pump (D9W)

043 2B Short cable from the computer to the heater fuel pump (D9W)

047 2F Short circuit of the fuel pump

048 30 No contact with the fuel pump


050 32 Heater run many times but have not worked (relay R3)

051 33 Flames emerged immediately after pressing the start button heater

052 34 No start (restart purge)

053 35 Stop flame during startup

36 054 Stop flame position max. productivity

055 37 Stop the flame in a position average performance

056 38 Stop the flame in the position of poor performance

057 39 Flame sensor short circuit (photoresist)

058 3A heater is turned off, but the flame in the combustion chamber (D2W)

059 3B Water temperature rising too quickly (D9W)

060 3C No contact with the sensor temperature control

061 3D sensor short circuit temperature control

062 3E No contact with the potentiometer (D2H / D2I)

3F 063 Short potentiometer (D2H / D2I)

064 40 No contact with flame sensor

065 41 Flame sensor short circuit

071 47 No contact with the sensor overheating (D3W / D9W)

072 48 Short-circuit overheating sensor (D3W / D9W)

073 49 Overheating sensor recorded the fastest increase in temperature (D9W)

090 5A Spontaneous error

091 5B high surge (high-voltage wires, CB-radio, etc.)

092 5C Faulty heater control unit - fault ROM

093 5D Faulty heater control unit - faulty RAM

094 5E Faulty heater control unit - fault EEPROM

096 60 Temperature sensor faulty heater ECU (D2I)

097 61 Faulty heater ECU (D2I / D2W / D9W)

255 FF cleared but faulty memory EEPROM