MERCEDES BENZ ACTROS,ATEGO,AXOR TRUCK FAULT CODES LIST part 3

Mercedes Truck UNIT FAULT CODE LIST MANAGEMENT TACHOGRAPH (DTCO)

Download
MERCEDES BENZ ACTROS,ATEGO,AXOR TRUCK FAULT CODES LIST PART 3
MERCEDES BENZ ACTROS,ATEGO,AXOR TRUCK FAULT CODES LIST PART 3
MERCEDES BENZ ACTROS,ATEGO,AXOR TRUCK FA
Adobe Acrobat Document 50.4 KB

0004 Open voltage supply cable

1000 CAN error

10000 Positioning drive tachograms violated

1100 CAN error

Internal Error 1200

1400 Calibration of the tachograph contains fault

1500 Fault Management details

1600 Fault Management details

1704 Connection CAN c dashboard INS is not properly

3408 Speed Sensor Malfunction

3504 Speed Sensor Malfunction

4804 output speed fault

8000 movement without drive tachograms

8100 Drive tachograms first driver missing

8200 Drive tachograms second driver missing

8300 Synchronization can be initiated

9000 Positioning drive tachograms violated

9600 Function drawer broken

9700 Faulty speed registration

9800 Faulty recorder system

9900 Faulty recorder system

Mercedes Benz LIST OF CONTROL UNIT FAULT CODES AUXILIARY HEATER (ZHE)

Faulty control unit 0000

0001 Malfunction of the control unit, the internal temperature sensor

0100 heater does not start

0104 Block of work after an unsuccessful launch

0200 flame interruption occurs again

0301 Overvoltage

0302 Undervoltage

0400 Premature flame recognition

0501 Flame sensor short circuit

0502 Open in a flame sensor circuit

0601 Short circuit Temperature sensor

0602 Break in the temperature sensor circuit

0701 Short metering pump

0702 Open circuit dosing pump

0801 Short-circuit the fan motor

0802 Open in a fan motor circuit

0803 Wrong fan motor speed

0901 Short glow plug

0902 Open circuit glow plug

1000 Overheating auxiliary heater

1004 Too many times overheating or excessive control took place (operation lock)

1101 Short circuit water pump

1102 Open in a water pump circuit

1201 Short circuit sensor setpoint

1202 Open circuit sensor setpoint

1301 Overheating sensor has a short circuit

1302 Overheating sensor has broken

1303 Overheating sensor is out of tolerance / operating range (detection redundancy check)

1401 Relay connection to the water pump has a short circuit

1501 Short circuit to connect external components

1601 Relay connection for the external fan is short-circuited

1620 Relay connection for the external fan is broken

1701 Fan excitement to switch water circuit is short-circuited

1702 Fan excitement to switch water circuit is open

Mercedes Truck LIST OF BLOCK ERROR CODES WS (MAINTENANCE SYSTEM)

0122 - CAN bus Overload

0123 - Functional CAN bus failure

0132 - Data WS control unit lifecycle wrong.

0133 - WS control unit parameters are incorrect.

0135 - Internal fault in the control unit

0138 - Internal fault in the control unit

0139 - Internal fault in the control unit

0150 - Timeout receiving CAN BU ABS data

0151 - CAN reception wait time data BU GS

0152 - CAN reception wait time data BU FR

0153 - CAN reception wait time data BU MR

0154 - CAN reception wait time data BU RS

0155 - CAN reception wait time data BU FR

0156 - CAN reception wait time data BU MR

0157 - Timeout receiving CAN data BU INS

0158 - Timeout receiving CAN data BU BS

0159 - CAN reception wait time data BU GS

0201 - oil temperature sensor has a fault KP "short to ground".

0202 - exceeded temperature sensor measuring range gearbox oil.

0205 - The measured value of the oil temperature sensor KP unreliable.

0210 - exceeded the maximum allowable temperature of the oil KP.

0301 - The temperature sensor transfer box has a fault "Short circuit to ground."

0302 - exceeded temperature sensor measuring range transfer case.

0305 - The measured value transfer gearbox temperature sensor is uncertain.

0310 - exceeded the maximum allowable temperature of the oil transfer case.

0401 - Temperature sensor front axle has a fault "Short circuit to ground."

0402 - exceeded range of front axle temperature sensor measurements.

0405 - The measured value of the front axle unreliable temperature sensor.

0410 - exceeded the maximum allowable temperature of the oil front differential.

0501 - rear axle temperature sensor has a fault "Short circuit to ground."

0502 - exceeded the range of the rear axle temperature sensor measurements.

0505 - The measured value of the rear axle unreliable temperature sensor.

0510 - exceeded the maximum allowable temperature of the rear differential oil.

0601 - condensed liquid sensor has a fault "Short Circuit" on the ground.

0604 - condensed liquid sensor has a fault "break a circuit."

0605 - value not valid condensation sensor.

1011 - Too much difference between the brake pad wear brakes 1st front axle.

1012 - Too much difference between the brake pad wear first front axle and the other axles.

1111 - Too much difference between the brake pad wear brakes 2nd front axle.

1112 - Too much difference between the brake pad wear second front axle and the other axles.

1211 - Too much difference between the brake pad wear brakes 1st rear axle.

1212 - Too much difference between the brake pad wear first rear axle and the other axles.

1311 - Too much difference between the brake pad wear brakes 2nd rear axle.

1312 - Too much difference between the brake pad wear second rear bridge and other bridges.

1401 - The closure of the signal line of the left sensor Brake pad wear 1st front axle.

1402 - The measured value of brake pad wear 1st front axle on the left above the measuring range.

1403 - The measured value of brake pad wear 1st front axle on the left below the measurement range.

1404 - Broken signal wire left sensor Brake pad wear 1st front axle.

1405 - invalid measurement value of brake pad wear 1st front axle on the left.

1420 - Failure of the CAN signal Brake pad wear 1, Front Axle Left

1501 - The closure of the signal line of the right sensor Brake pad wear 1st front axle.

1502 - The measured value of brake pad wear 1st front axle on the right above the measuring range.

1503 - The measured value of brake pad wear 1st front axle on the right below the measurement range.

1504 - Open the right signal wire sensor Brake pad wear 1st front axle.

1505 - invalid measurement value of brake pad wear 1st front axle on the right.

1520 - Failure of the CAN signal Brake pad wear 1, Front Axle Right

1601 - The closure of the signal line of the left sensor Brake pad wear 2nd front axle.

1602 - The measured value of brake pad wear of the 2nd front axle on the left above the measuring range.

1603 - The measured value of brake pad wear of the 2nd front axle on the left below the measurement range.

1604 - Broken signal wire left sensor Brake pad wear 2nd front axle.

1605 - invalid measurement value of brake pad wear of the 2nd front axle on the left.

1620 - Failure of the CAN signal Brake pad wear 2nd front axle Left

1701 - The closure of the signal line of the right brake pad wear indicator 2nd front axle.

1702 - The measured value of brake pad wear of the 2nd front axle on the right above the measuring range.

1703 - The measured value of brake pad wear of the 2nd front axle on the right below the measurement range.

1704 - Broken signal wire of the right brake pad wear indicator 2nd front axle.

1705 - invalid measurement value of brake pad wear of the 2nd front axle on the right.

1720 - Failure of the CAN signal Brake pad wear 2nd front axle Right

1801 - The closure of the signal line of the left sensor Brake pad wear 1 st rear axle.

1802 - The measured value of brake pad wear 1st rear axle on the left above the measuring range.

1803 - The measured value of brake pad wear 1st rear axle on the left below the measurement range.

1804 - Broken signal wire left sensor Brake pad wear 1 st rear axle.

1805 - invalid measurement value of brake pad wear 1st rear axle left.

1820 - Failure of the CAN Brake pad wear 1 st rear axle to the left signal

1901 - The closure of the signal line of the right sensor Brake pad wear 1 st rear axle.

1902 - The measured value of brake pad wear 1st rear axle on the right above the measuring range.

1903 - The measured value of brake pad wear 1st rear axle on the right below the measurement range.

1904 - Open the right signal wire sensor Brake pad wear 1 st rear axle.

1905 - invalid measurement value of brake pad wear 1st rear axle right.

1920 - Failure of the CAN Brake pad wear 1 st rear axle right signal

2001 - The closure of the signal line of the left sensor Brake pad wear 2nd rear axle.

2002 - The measured value of brake pad wear 2nd rear axle on the left above the measuring range.

2003 - The measured value of brake pad wear 2nd rear axle on the left below the measurement range.

2004 - Broken signal wire left sensor Brake pad wear 2nd rear axle.

2005 - invalid measurement value of brake pad wear 2nd rear axle left.

2020 - Failure of the CAN signal Brake pad wear 2nd rear axle Left

2101 - The closure of the signal line of the right sensor Brake pad wear 2nd rear axle.

2102 - The measured value of brake pad wear 2nd rear axle on the right above the measuring range.

2103 - The measured value of brake pad wear 2nd rear axle on the right below the measurement range.

2104 - Open the right signal wire sensor Brake pad wear 2nd rear axle.

2105 - invalid measurement value of brake pad wear 2nd rear axle right.

2120 - Failure of the CAN signal Brake pad wear 2nd rear axle Right

2205 - invalid measurement value (signal path) tachograph.

2320 - Failure of the CAN signal 'Residual pressure circuit 1 or 2' (INS)

3105 - Not Actual speed signal NW.

3120 - Failure of NW speed via CAN signal

3220 - Failure of the CAN speed signal

3320 - Failure of the setpoint signal via the CAN motor torque

3420 - Failure of the CAN signal measured value outside air temperature

3520 - Failure of the CAN signal measured value air filter is clogged

4105 - invalid measurement of oil temperature in the retarder brake (retarder).

4110 - exceeded the maximum allowable temperature of the oil in the retarder brake (retarder).

4120 - Failure of the CAN signal is the measured value of oil temperature in the retarder brake (retarder)

5105 - invalid measurement value of the oil temperature in the engine.

5110 - exceeded the maximum allowable temperature of the oil in the engine.

5113 - Improper engine oil viscosity.

5120 - Failure of the CAN signal is the measured value of oil temperature in the engine

5205 - invalid measurement value of the coolant temperature.

5210 - exceeded the maximum permissible coolant temperature.

5220 - Failure of the CAN signal of the measured value of the coolant temperature

5320 - Failure of the CAN signal measured fuel consumption values

7120 - Failure of the CAN actual value of the clutch signal